Quiana and Fandango 1.0 p 1 OWNERS MANUAL Version 1.0 July, 2002
Quiana and Fandango 1.0 p 10 Mains Fuse – Quiana 100 and Fandango 100 For 100VAC versions, the Mains Fuse is: 5 Amp, 250 Volt Slo-Blo type (size
Quiana and Fandango 1.0 p 11 appropriately set to match the given load). If it has to drive speaker loads lower than 2 ohms, its output transformer
Quiana and Fandango 1.0 p 12 Note: Loads that are not matched properly may harm your amp. If unequal speaker cabinets loads, i.e. a 4 ohm cabinet a
Quiana and Fandango 1.0 p 13 Before you connect a signal processor to your amp, either turn the amp off or to standby. Use high-quality shielded cor
Quiana and Fandango 1.0 p 14 Driving one external speaker cabinet WARNING: TO REDUCE THE RISK OF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHIS EQUIPMENT
Quiana and Fandango 1.0 p 15 Driving two speaker cabinets WARNING: TO REDUCE THE RISK OF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHIS EQUIPMENT TO RAIN
Quiana and Fandango 1.0 p 16 Slaving a second Quiana/Fandango WARNING: TO REDUCE THE RISK OF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHIS EQUIPMENT TO
Quiana and Fandango 1.0 p 17 Placing a signal processor in the effects loop INPUTOUTPUTZ IN250K ΩZ OUT560 ΩRETURNRETURNLEVELLEVELSENDSENDEFFECTS
Quiana and Fandango 1.0 p 18 filters, and as the signal from the Line Out is full frequency, not affected by the mechanical-acoustic filter of a spe
Quiana and Fandango 1.0 p 19 Clean your amp once in a while You can use a damp but not wet cloth, or one moistened in a weak solution of dishwashin
Quiana and Fandango 1.0 p 2 Introduction Your Rivera Amp Is An Important Part Of Your Sound Your sound is your signature, your mark, your voice. An
Quiana and Fandango 1.0 p 20 3. After 25 minutes, turn it on, and if it shuts down again, refer the amp to qualified service personnel. Note: On SE
Quiana and Fandango 1.0 p 21 Location Type V1 12AX7A V2 12AX7A V3 12AX7A V4 12AX7A V5 12AX7A V6 6L6GC(Quiana), EL-34 (Fandango) V7
Quiana and Fandango 1.0 p 22 Turn off the amp, and allow the tubes to cool. Now pull out the troublesome tube and replace it with one of the same v
Quiana and Fandango 1.0 p 23 1. Let the power tubes cool. Remember the way the eight pins are arranged, and note that the center hole on the tube so
Quiana and Fandango 1.0 p 24 7FemalesocketsViewedfromamplifierbackpanelChannelSwitchChannelLEDNinjaBoostSwitch/LEDBoostSwitch/LED+18VD
Quiana and Fandango 1.0 p 25 Quiana 50/100 and Fandango 55/100 Specifications High-gain input impedance: 1 Megohm Low-gain input impedance: 33k ohm
Quiana and Fandango 1.0 p 26 Warranty Subject to the Obligations and Exclusions found below, this RIVERA product is warranted against manufacturing
Quiana and Fandango 1.0 p 27 and/or do not allow the exclusion or limitation of consequential damages, so the above limitations on implied warranty
Quiana and Fandango 1.0 p 3 Packing Information Unpacking Before you plug in, inspect your Quiana/Fandango amp for any damage. Your amp was inspec
Quiana and Fandango 1.0 p 4 connected. For countries where 220 to 240 volts AC is encountered, make sure that you have the correct power cord. Our
Quiana and Fandango 1.0 p 5 Quick Start Settings If you're looking for a good starting point, try these settings. Remember that every guitar a
Quiana and Fandango 1.0 p 6 Front Panel HIGHGAINGAINLOWSELECTVOLUMEBASSMIDDLETREBLEMASTERVOLUMETREBLEMIDDLEBASSMASTERREVERBPRESENCEFOCUSWARMNINJANOT
Quiana and Fandango 1.0 p 7 Middle Quiana only The midrange circuit provides the "meat" that fills out your sound. It has a slight notch
Quiana and Fandango 1.0 p 8 especially if you're looking for a uniquely expressive rhythm texture.Typically, a humbucking equipped guitar alrea
Quiana and Fandango 1.0 p 9 on, always check that a speaker is connected and that the power cord is firmly plugged into the amp and the outlet. Rea
Comments to this Manuals